La Marzocco Modbar AV repair that shows up today. GTA-wide.

The seal in the tap collar wears and lets water weep at the surface. We pull the tap, fit a new seal kit, and verify clean operation at the bar. It is a contained job that does not need the whole under-counter module pulled apart.

Either the cable running between the bar tap and the under-counter module is intermittent, or the bar-side controller has failed. We trace the cable, replace it if it is damaged, and test the controller. The cabling is the usual culprit on a split system.

That is the normal way these are built. We access the under-counter module to reach the boiler, pump, gicleur, solenoids, and controller, and only the tap work happens up top. As long as the cabinet is accessible, a Modbar service is no slower than a countertop machine.

Almost certainly. Modbar modules need clearance to breathe, and a tight or sealed cabinet starves them of air so they overheat and trip thermal cutouts. We confirm the install meets La Marzocco's ventilation spec, add ducting if the cabinet is too tight, and reset the cutouts.

Yes. It is usually a clogged gicleur in that tap's under-counter group. We pull it, clean it ultrasonically, and verify flow at the tap. If pressure is low across the board, we check the rotary pump instead.

Yes. The flow meters in the under-counter module mineralize and pulse unevenly. We clean each meter and reprogram the doses by weight, the same as on a countertop machine, just accessed from below.

Much of the core is shared: saturated group, dual boiler, gicleurs, solenoids, and flow meters. The Modbar-specific parts are the tap assembly, its seal kits, and the bar-to-module cabling, all of which we carry or source for these installs.

Yes. The Steam module is the dedicated under-counter steam boiler that feeds a tap on the bar, and we service it alongside the AV: descaling, element and pressure stat work, and the steam valve in the tap. One visit covers the whole bar.

Flat rate for the visit, parts billed at their actual cost on top. You'll hear the rate when you book, and for bigger jobs we quote in writing on-site before any work starts. No estimate that balloons mid-job.

Same-day. Call in the morning and a technician is usually on-site before the day is out; calls placed later in the day book for the next morning. Urgent breakdowns get priority routing.

The GTA and most of the Golden Horseshoe: Toronto through Mississauga, Vaughan, and Markham, out to Oshawa, Hamilton, and Niagara. If you're not sure you're in range, call and we'll tell you straight.

No. We work call by call. Plenty of customers put us on a maintenance schedule eventually, but that's their choice after seeing the work, never a requirement.

Parts carry their manufacturer warranty, and we stand behind our labour: if the same fault recurs, call us and we'll review it. Specific terms are discussed upfront on each job, not promised in marketing copy.

On-site whenever possible, which is most of the time. If a job genuinely needs the bench, like a full boiler rebuild or major electronics work, we'll say so before anything leaves your building.

Call us or send the form on this page. We confirm the machine, the fault, and a time window the same day. If it's urgent, say so and we'll route the nearest technician.

Diagnosis first: we confirm the fault, tell you what caused it, and quote the fix before touching a wrench. Most repairs finish in that same visit because the common wear parts ride on the truck.

High-wear parts for the platforms we service constantly ride on the truck. Anything else we order, usually next-day where suppliers allow, and we tell you the lead time before committing you to anything.

Usually, yes. We service legacy machines for as long as parts can be sourced, and we're honest when a repair stops making financial sense against a replacement. You get the math, you make the call.

Often, but that's not the pitch. We quote against the actual work, not a factory pricing book, and we'll tell you when a manufacturer warranty claim is the better route. Transparency is the value; the price usually follows.

Yes, and we do it by default on the way out. Half of repeat faults trace back to skipped daily cleaning or wrong routine, so the technician walks your team through what actually matters before leaving.