Rex-Royal service, independent and upfront
S200 dead in the break room or behind the lobby bar? We repair Rex-Royal machines for offices, hotels, and QSR. Milk system faults, brew unit jams, frozen touchscreens, failed sensors: most repairs finish on the first visit from truck stock. Independent specialists, no manufacturer affiliation. Built for small to medium volume.
We'll get back to you today.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email support@grajqevci.com.
Rex-Royal · Small to mid-volume super-automatic
The Rex-Royal S200 is the small-to-medium machine in the Swiss-made S-Series, suited to offices, bakeries, takeaways, petrol stations, and retail counters. It runs a metal brewing unit, a variable precision grinder, and a 7 inch touchscreen that programmes up to 24 drinks, with interchangeable bean and product containers up to 1.8 kg and individually adjustable brewing pressure. It is a steady daily workhorse, and we keep the brew unit, grinder, milk side, boiler, and controls running across the GTA.
From recent service calls
Why Grajqevci
Call in the morning and a technician is usually on-site before the day is out. Most Rex-Royal S200 jobs get diagnosed and fixed on the first visit.
Commercial coffee equipment is all we do, and Rex-Royal S200 is one of the platforms we know best. Not a generalist guessing at a service manual. Genuine OEM parts, industry-standard procedures.
Flat rate for the visit, with parts billed separately. For bigger jobs you'll see a written quote on-site before we proceed.
Skip the wait
Trusted by Toronto's most demanding teams
S200 faults we diagnose
Below are the most common Rex-Royal S200 faults we see on service calls, with what causes each and how we resolve it.
Packed grounds, a swollen seal, or a worn drive part stall the brew unit. We strip it, clear the chamber, replace the seals and any worn part, lubricate with food-safe grease, and verify clean cycling.
A torn screen, a worn piston seal, or grind drift. We inspect the brew unit, replace worn screens and seals, measure brew pressure, and recalibrate the grind and dose.
The S200's adjustable brewing pressure can be set out of range or drift with seal wear. We measure pressure with a calibrated gauge, reset it to the recipe target, and replace worn brew seals if they will not hold.
Scale insulating the element or element fatigue. We descale, test resistance, and replace the element if output does not recover.
A weeping fitting or a worn seal. We pressure-test, dye-trace the leak, and replace the failed part rather than retighten it.
Burr wear or a grind-setting that has slipped. We weigh the dose across a run of shots, measure the burr gap, reset the grind, recalibrate the dose, and replace the burrs if they are past spec.
A foreign object, bridged beans, or a stuck container gate. We open the grinder, clear it, inspect the burrs, and confirm the container feeds consistently.
A firmware hang or a fault on a sensor, valve, or board. We reset, read the fault log, address the root cause, and clear the code.
A drawer not seated or a full-drawer sensor misreading. We check the drawer sensor and replace it if it reads unreliably.
Residue in the foam path, a worn intake part, or a milk-temperature sensor out of spec. We strip and sanitise the milk circuit, replace worn parts, test the sensor, and verify foam quality across the menu.
Your coffee emergency ends here
Call or submit the form. We confirm your address, model, and the issue.
An experienced technician arrives, runs full diagnostics, and identifies the root cause.
You receive a flat, itemized quote. Nothing proceeds without your green light.
We complete the repair, run a test cycle, and walk you through what to watch for.
Parts on the truck
By the numbers
Property management portfolio with executive-floor espresso programs. Their technicians are the only outside vendors we let in our boardroom-adjacent kitchens.
*Estimated based on the approximate distance from our nearest service centre, average commute time, and median service-call length for one machine. Prices in Canadian dollars (CAD $). Final quote provided on-site after diagnosis.
FAQ
22 answers covering service, repair, parts, installation, warranty, and edge cases.
Updated August 2026
Yes. The Rex-Royal S200 is a regular service call for us across office floors, hotel lobbies, and hospitality break rooms in the GTA. The high-wear parts ride on the truck, and our technicians work on this exact platform routinely. Independent service, not affiliated with Rex-Royal. Built for mid-volume daily operations.
By call volume on the S200: metal brew unit jamming or stuck mid-cycle; grounds in the cup or weak shot; brew pressure off target after a recipe change. Milk module contamination, brew unit cam wear, controller-board firmware issues, and grinder dose drift are the recurring service categories. Most are diagnosed and fixed on the first visit when the part is on the truck.
No. We're independent, and we'd rather say that plainly than imply otherwise. We service the S200 because it's a platform we work on constantly, and that independence lets us quote transparently, work outside warranty, and take on older units the authorized network may decline.
Most S200 repairs finish in a single visit of 60 to 120 minutes. Brew unit overhauls and milk system rebuilds run longer, usually 2 to 3 hours. If a part isn't on the truck, we diagnose on the first visit and come back the next business day to finish.
Flat rate for the visit, parts billed separately. Smaller repairs just get invoiced after the work. Bigger jobs get a written quote on-site, and nothing major starts until you've approved it.
Yes. Milk system contamination, brew unit cam follower wear, and sensor drift are the call patterns. We disassemble, sanitize, replace what's worn, and verify foam quality before sign-off.
The common service parts, yes: brew unit seals, milk system O-rings, frequent sensors, pump assemblies, and screens. Less common parts (specific board revisions, full brew unit assemblies) come through the distributor network in 1 to 3 business days.
Where it matters, yes: brew units, electronic boards, sensors, pumps, motors. For O-rings, tubing, and other commodity components, industry-standard parts that meet or exceed OEM spec sometimes get your machine running sooner, and we tell you which we're fitting before it goes in.
Yes. A S200 install covers the site survey, power and water assessment, water filtration spec, plumbing and electrical hookup, calibration of every drink profile, and staff training on daily operation and cleaning.
Quote to commissioning usually runs 5 to 10 business days, gated mostly by filtration lead times and any plumbing or electrical work the site needs. The install visit itself takes 3 to 5 hours including calibration and training. Timing is confirmed in writing once the site survey is done.
Yes, tuned to your daily volume. A S200 pushing 150+ drinks a day gets quarterly visits; lighter use runs semi-annual. Every maintenance call covers descaling, brew unit overhaul, milk system sanitation, grinder calibration, and a full functional test.
Up to 50 drinks a day, every 6 months. From 50 to 150, every 4 months. Past 150, every 3 months. Harder water shortens those intervals (Toronto's is moderate), and daily cleaning by your staff is non-negotiable no matter which schedule you're on.
If your S200 is under Rex-Royal's warranty, independent service can affect that coverage depending on the manufacturer's terms. Try the authorized network first for a covered defect. If they're slow or decline, call us and we'll service it on standard terms.
Then you're our typical customer. Out-of-warranty S200 machines are the bulk of our service work, and they get the same treatment as anything else: real diagnostics, genuine parts where it matters, flat-rate visit with parts billed separately, no contracts.
Usually, yes. We keep older Rex-Royal platforms running long after other shops have stopped supporting them. Out-of-production parts come from refurbisher networks or quality-matched aftermarket equivalents. And if the repair isn't economical, we tell you straight rather than running up the cost.
When the repair crosses roughly 50% of a refurbished replacement on a machine past 8 to 10 years of heavy daily use, or when several major systems fail in the same visit. We give you honest math on this. We'd rather you replace than pay us to fix something that breaks again next month.
Yes. Water hardness is the single biggest factor in how long a S200 lasts. Scale shortens element life, restricts flow, and triggers descale cycles more often. We test your water on-site, spec the right cartridge or system, and install it during maintenance or as its own visit.
Yes. If there's an error code on the S200 screen, call with the code and a quick description of what's happening. We can often identify the fault before dispatching, which means the right parts arrive on the first visit instead of a return trip.
Have the model and serial number ready (rear panel of the machine), note any error codes from the past week, and clear access around the machine. If the fault is intermittent, try to reproduce it before we arrive so the technician can see it live.
Yes. Every installation includes full training: daily cleaning, basic troubleshooting, drink programming, and what to watch for. After a repair, the technician walks your staff through what was fixed and what to monitor in the coming weeks. Standalone refresher visits are available too.
Often, yes. S200 calls within Toronto and the immediate GTA can usually be dispatched the same day. Same-day completion depends on parts: the high-frequency ones ride on the truck, rarer ones can push the fix to the next business day.
Toronto, Mississauga, Brampton, Vaughan, Markham, Richmond Hill, Oakville, Burlington, Hamilton, and the wider Greater Toronto Area. Outside that range? Call with your postal code and we'll tell you straight whether it makes sense for us to come out.
Call the team that works on Rex-Royal machines all the time.
Call (289) 217-3796 now →