!
Group gasket weeping
A weeping group gasket is standard 12-to-18-month wear. We replace the gasket and dispersion screen together and confirm the seal under pressure.
Value workhorse, back in service
Pegaso Plus down with a line out the door? This is one of the machines we see most, so the faults are familiar: a group gasket weeping, the steam boiler not keeping up at peak, volumetric doses drifting, a pump hammering on startup. Tell us the model and the symptom and we usually repair it in a single visit.
We'll get back to you today.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email [email protected].
Wega · High-volume traditional espresso
The Pegaso Plus is the current take on Wega's long-running Pegaso, the brand's entry-level value workhorse. Built for cafe volume up to 400 shots a day, it comes in EVD electronic or EPU semi-automatic trims, with a backlit push-button panel and an LED-lit work surface. From the service side it is honest, simple hardware: group seals, steam valves, a flow meter, and a pump are the parts that come up, and they are all quick to put right.
Why Grajqevci
Call in the morning and a technician is usually on-site before the day is out. Most Wega Pegaso Plus jobs get diagnosed and fixed on the first visit.
Commercial coffee equipment is all we do, and Wega Pegaso Plus is part of the weekly rotation. Not a generalist guessing at a service manual. Genuine OEM parts, industry-standard procedures.
Flat rate for the visit, with parts billed separately. For bigger jobs you'll see a written quote on-site before we proceed.
Skip the wait
Trusted by Toronto's most demanding teams
Pegaso Plus faults we diagnose
Below are the Pegaso Plus faults that fill our service log, from weeping group gaskets to drifting volumetric doses, each with the usual cause and how we put it right.
A weeping group gasket is standard 12-to-18-month wear. We replace the gasket and dispersion screen together and confirm the seal under pressure.
An oil-clogged screen breaks up even extraction, so we fit a fresh one and backflush the group with detergent to clear the rest of the path.
Brew pressure under 9 bar is pump wear or OPV drift. We gauge it with a blind portafilter, adjust the OPV, and quote a pump only if output has dropped below spec.
Hammering at startup is air in the line or a worn rotary. We bleed the line, open the pump head to check the vane, and replace it if it is worn.
On a multi-boiler Pegaso, temperature drift at a group is sensor wear or PID drift. We measure each group, recalibrate the PID, and replace the sensor if it is reading off.
Low steam pressure is scale, a tired element, or a drifted pressurestat. We descale the boiler, test the element, and check the pressurestat against a gauge before deciding what to replace.
Water under the machine gets pressure-tested circuit by circuit so we can isolate the leak and replace the seal or fitting behind it.
Drain backflow is a blocked or kinked drain line. We clear it and confirm it runs freely under load.
A wand dripping when closed is a worn valve cartridge. We rebuild the valve with a new cartridge and seals and confirm a dry shut-off.
Steam that fades during a rush is the boiler not keeping up. We descale, test the element, and verify the pressurestat so it recovers under load.
Drifting volumetric doses are flow-meter buildup. We clean the impeller, confirm the pulse signal, and reprogram the doses against a calibrated shot glass.
A dead display or keypad on one group points at that group's controller or wiring. We trace the fault to the affected part and replace it.
Auto-fill that cycles too often is a scaled level probe or a slow boiler leak. We descale the probe first, then pressure-test the boiler for hidden seepage.
Uneven cup-warmer heat is a failing element or a tripped thermal cutoff. We test both and replace whatever is out of spec.
Your coffee emergency ends here
Call or submit the form. We confirm your address, model, and the issue.
An experienced technician arrives, runs full diagnostics, and identifies the root cause.
You receive a flat, itemized quote. Nothing proceeds without your green light.
We complete the repair, run a test cycle, and walk you through what to watch for.
Parts on the truck
Receipts
Multi-property hotel group across the GTA. One point of contact, monthly invoicing, scheduled maintenance that actually shows up. Took us off the firefighting cycle.
*Estimated based on the approximate distance from our nearest service centre, average commute time, and median service-call length for one machine. Prices in Canadian dollars (CAD $). Final quote provided on-site after diagnosis.
FAQ
20 answers covering service, repair, parts, installation, warranty, and edge cases.
Updated July 2026
EVD is the electronic, volumetric version that meters each dose automatically, while EPU is the semi-automatic trim where the barista controls the shot manually. They share the same boiler, group, and steam hardware, so most repairs are identical; the EVD just adds the flow meters and dose programming we calibrate.
Yes, that is its design point, and the multi-boiler top trims hold up well at that volume. Push it hard and the wear parts simply arrive sooner, so a busy bar benefits from a regular descale and seal service rather than a bigger machine.
That is the steam boiler not keeping up, usually because scale is insulating the element or the pressurestat has drifted. We descale, test the element, and verify the pressurestat against a gauge so it recovers properly under load.
Mineral buildup on the flow meter, almost every time. We clean the impeller, confirm the pulse signal back to the controller, and reprogram the doses against a calibrated shot glass.
Mechanically it is the same machine with taller group spacing for bigger cups, so the repairs are identical. We just account for the extra plumbing run when we trace a leak.
Yes. Earlier Pegaso builds share most of their parts with the current Plus and with Astoria, so we keep them running comfortably and only flag a part when it is genuinely discontinued.
For nearly every fault, yes. Group seals, steam valves, a flow meter, or a pump are small money against a new machine, and a Pegaso Plus has plenty of working life in it. We give you the number and an honest read either way.
It depends on your water and your volume, but a busy bar on harder local water often wants it every couple of months. Skipped descaling is the single biggest reason these machines come to us heating slowly or throwing steam faults.
Flat rate for the visit, parts billed at their actual cost on top. You'll hear the rate when you book, and for bigger jobs we quote in writing on-site before any work starts. No estimate that balloons mid-job.
Same-day in most cases. Call in the morning and a technician is usually on-site before the day is out; calls placed later in the day book for the next morning. Urgent breakdowns get priority routing.
The GTA and most of the Golden Horseshoe: Toronto through Mississauga, Vaughan, and Markham, out to Oshawa, Hamilton, and Niagara. If you're not sure you're in range, call and we'll tell you straight.
No. We work call by call. Plenty of customers put us on a maintenance schedule eventually, but that's their choice after seeing the work, never a requirement.
Parts carry their manufacturer warranty, and we stand behind our labour: if the same fault recurs, call us and we'll review it. Specific terms are discussed upfront on each job, not promised in marketing copy.
On-site whenever possible, which is most of the time. If a job genuinely needs the bench, like a full boiler rebuild or major electronics work, we'll say so before anything leaves your building.
Call us or send the form on this page. We confirm the machine, the fault, and a time window the same day. If it's urgent, say so and we'll route the nearest technician.
Diagnosis first: we confirm the fault, tell you what caused it, and quote the fix before touching a wrench. Most repairs finish in that same visit because the common wear parts ride on the truck.
High-wear parts for the platforms we service constantly ride on the truck. Anything else we order, usually next-day where suppliers allow, and we tell you the lead time before committing you to anything.
Usually, yes. We service legacy machines for as long as parts can be sourced, and we're honest when a repair stops making financial sense against a replacement. You get the math, you make the call.
Often, but that's not the pitch. We quote against the actual work, not a factory pricing book, and we'll tell you when a manufacturer warranty claim is the better route. Transparency is the value; the price usually follows.
Yes, and we do it by default on the way out. Half of repeat faults trace back to skipped daily cleaning or wrong routine, so the technician walks your team through what actually matters before leaving.
Call the team that works on these machines week in, week out.
Call (289) 217-3796 now →