Scale-proof your Wilbur Curtis: filter sizing, swaps & RO. GTA-wide.
Wilbur Curtis ships its own branded cartridge line, the CSC5CC00 (5") and CSC10CC00 (10") quick-disconnect cartridges with HydroBlend chemistry. On higher-volume sites and on G3 / G4 ThermoPro installs, dealers regularly substitute Everpure 7CB5-S or Pentair Everpure Claris L.
We'll measure your water and size the cartridge to your machine.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email support@grajqevci.com.
Our recommendation
The filter we put on Wilbur Curtis machines.
Wilbur Curtis uses both stages, a proprietary in-machine cartridge for fine filtration plus an upstream cartridge for bulk hardness and chlorine. Sized together, the two stages extend each other's life and keep scale off the boiler on hard GTA water.
Our pickPentair Everpure
Recommended filter · Wilbur Curtis
Pentair Everpure 7CB5-S
High-volume batch-brewer default
Fitted ahead of the machine, so scale never reaches it
Sized to your measured daily volume, bypass dialed to your feed water
Logged in our PM system and swapped before it exhausts
Your Wilbur Curtis cartridge swap calendar, by city.
Cartridge capacity is rated at 10°dKH. Local GTA hardness varies, so the same cartridge runs longer in soft Toronto water than in hard Hamilton water. Find your city, get your swap interval.
Intervals assume a single cartridge sized to typical site volume. Capacity-tracked PM beats calendar-only PM, we measure feed water at commissioning and tune your specific schedule from there. Hardness data: municipal water-quality reports, updated annually.
When to swap your cartridge
Replacement signals on Wilbur Curtis.
Cartridge exhaustion shows up well before the machine actually fails. Tick anything you're seeing right now and we'll read the pattern.
Should have been 10", exhausted carbon in 6 months
Our fix
Step up to CSC10CC00 or Everpure 7CB5-S.
Issue
Chlorine-tasting coffee after cartridge expired
Cause
Carbon stage exhausted
Our fix
Replace cartridge.
What happens if you skip Wilbur Curtis filtration
Scale damage compounds on an unfiltered install.
Nothing looks wrong for months, which is exactly why unfiltered machines fail early. Here's how the damage escalates.
Months 0-6Cosmetic
No visible signs. Scale begins precipitating onto the heating element and brew boiler. Cup quality unchanged.
Months 6-12Early wear
Visible scale at the steam tip and dispense spout. Heat-up time creeps past baseline. Carbon stage exhausts; cup tastes flat or chlorinated.
Months 12-24Degrading
Milk foam quality degrades. Brew-temperature stability drifts as boiler insulation worsens. Relief valves start sticking. Service-call frequency climbs.
Years 2-4Failure
Heating-element failure becomes common. Brew-group reseal cycles shorten. Pinhole leaks in boiler tubing. Warranty void from documented scale damage.
Year 5+Terminal
Catastrophic component failure on a 12-year platform. The repair-vs-replace tipping point hits a decade earlier than it should have.
Our Wilbur Curtis filter service
How we keep your Wilbur Curtis machine running.
We service Wilbur Curtis G3 / G4 ThermoPro, Gemini, and Alpha across GTA office and foodservice sites. We carry Curtis CSC5CC00 and CSC10CC00 plus Everpure 7CB5-S.
*These are conservative starting points, not Wilbur Curtis factory numbers. A water test or the machine's own counter can safely stretch them. Talk to us before changing a schedule that already works.
FAQ
Wilbur Curtis filter questions, answered.
7 answers covering cartridges, intervals, warranty, and the local water profile.
What filter does my Wilbur Curtis take?
Wilbur Curtis uses Curtis CSC5CC00 or Curtis CSC10CC00 as the OEM cartridge, plus optional upstream filtration on higher-volume installs. See the cartridge spec table above for part numbers, capacity, and replacement intervals.
How often should I replace my Wilbur Curtis filter in the GTA?
Cartridge capacity is rated at 10°dKH. In moderate-hardness Toronto / Mississauga water, expect 9 to 12 months on a properly-sized cartridge. In harder York Region and Hamilton water, drop to 6 to 9 months. The full city-by-city schedule is in the GTA schedule table above.
Does Wilbur Curtis require a specific filter brand for warranty?
Wilbur Curtis doesn't mandate a specific brand but requires water in spec (typically 4-8°dH after the cartridge). Most installs default to Pentair Everpure. We document the install for warranty traceability.
Do I need both the in-machine cartridge and an upstream filter?
On high-volume installs, yes. The in-machine cartridge (AquaClean, CLARIS Pro, AquaBasic, etc.) handles short-cycle fine-filtration and the machine's firmware tracks it. An upstream cartridge handles the bulk hardness and chlorine load so the in-machine cartridge can focus on the polish stage. On low-volume office installs the in-machine cartridge alone is enough; on cafe / hospitality volume the dual setup extends in-machine cartridge life dramatically.
Do you carry the cartridges in your van for same-visit service?
Yes for the platforms we work on most, BWT Bestmax M/L/XL, Pentair Everpure Claris Ultra, Jura CLARIS Pro Smart, Saeco AquaClean CA6903, WMF AquaBasic V/M/XL, and Curtis CSC5CC00/CSC10CC00 ride on the truck. Less common cartridges (some Optipure tiers, Elektra Kwts factory softener, Melitta Cafina-branded) are ordered ahead of the visit so we land with the right part on the first trip.
Will you set up a maintenance schedule so I don't have to track it?
Yes. We commission with the install date logged against the cartridge's capacity rating and the site's measured daily volume. Our PM schedule lands cartridge swaps before exhaustion, descales the machine when the cartridge is being changed (so scale never reaches the boiler), and sends you the service log so you have warranty traceability for the manufacturer.
How much does a filter install or replacement actually cost?
Cartridge cost varies by tier, a single BWT Bestmax Premium L runs around $180 to $230 CAD, an Everpure Claris Ultra 500 sits in the same range. Installation labour on a new upstream loop is typically 1.5 to 2.5 hours depending on plumbing access. Routine cartridge swaps on an existing head are a 15-minute visit, usually folded into a PM call to save you a separate truck roll. We quote in writing before any work.
What we've done
What two-and-a-half decades on the road looks like.
"
Our boiler failed during a Saturday brunch service and they had us pulling shots again before close. Same-day weekend dispatch.
Sofia · Brunch Restaurant · Yorkville
25+1
Years servicing equipment
4 hr2
Avg GTA response
92%3
First-visit resolution
4.74
Average client rating
1 Continuous service operations across the GTA since 2001. 2 Median on-site arrival window for urgent GTA calls placed during business hours. 3 Internal service tracking, 2024 to 2025 calendar years. 4 Calculated from verified client feedback over the past 24 months.
Wilbur Curtis cartridge replacement, sized to your water.
We measure feed-water hardness on every install, dial the bypass to the manufacturer window, and put cartridges on capacity-tracked PM so nothing scales the boiler.
