Slayer water treatment by the people who fix the machines. GTA-wide.
Slayer's manual: hardness should land at 4-5 grains after treatment; carbon filtration is required. Slayer endorses both Optipure and BWT by name. Ion-exchange-only softeners are NOT appropriate for the stainless boilers, they pit the boiler from inside. Espresso, Espresso V3, Single Group, Steam EP, Steam LP, Steam Single all share this spec.
We'll measure your water and size the cartridge to your machine.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email support@grajqevci.com.
Our recommendation
The filter we put on Slayer machines.
Slayer water treatment is dealer-installed upstream, an in-line cartridge between the building supply and the machine inlet, sized to your daily volume and dialled to local hardness. The machine doesn't track it, so the swap lives on a scheduled PM, not a warning light.
Our pickBWT
Recommended filter · Slayer
BWT Bestmax Premium
Equally endorsed in the manual
Fitted ahead of the machine, so scale never reaches it
Sized to your measured daily volume, bypass dialed to your feed water
Logged in our PM system and swapped before it exhausts
Cartridge capacity is rated at 10°dKH. Local GTA hardness varies, so the same cartridge runs longer in soft Toronto water than in hard Hamilton water. Find your city, get your swap interval.
Intervals assume a single cartridge sized to typical site volume. Capacity-tracked PM beats calendar-only PM, we measure feed water at commissioning and tune your specific schedule from there. Hardness data: municipal water-quality reports, updated annually.
When to swap your cartridge
Replacement signals on Slayer.
Cartridge exhaustion shows up well before the machine actually fails. Tick anything you're seeing right now and we'll read the pattern.
Quote boiler replacement; install Optipure RO with remineralization going forward.
Issue
Brew temperature stability drifting
Cause
Carbon stage exhausted, chlorine breakthrough
Our fix
Replace cartridge.
What happens if you skip Slayer filtration
Scale damage compounds on an unfiltered install.
Nothing looks wrong for months, which is exactly why unfiltered machines fail early. Here's how the damage escalates.
Months 0-6Cosmetic
No visible signs. Scale begins precipitating onto the heating element and brew boiler. Cup quality unchanged.
Months 6-12Early wear
Visible scale at the steam tip and dispense spout. Heat-up time creeps past baseline. Carbon stage exhausts; cup tastes flat or chlorinated.
Months 12-24Degrading
Milk foam quality degrades. Brew-temperature stability drifts as boiler insulation worsens. Relief valves start sticking. Service-call frequency climbs.
Years 2-4Failure
Heating-element failure becomes common. Brew-group reseal cycles shorten. Pinhole leaks in boiler tubing. Warranty void from documented scale damage.
Year 5+Terminal
Catastrophic component failure on a 12-year platform. The repair-vs-replace tipping point hits a decade earlier than it should have.
Our Slayer filter service
How we keep your Slayer machine running.
We follow Slayer's water spec to the letter, no ion-exchange-only softeners. We stock Optipure cartridges and BWT Bestmax for in-spec sites, and quote full Optipure RO with magnesium remineralization where the feed water demands it.
*Cautious by design, not pulled from a Slayer manual. Machine water counters and a measured hardness test earn you longer intervals. Check with us first if a schedule is already in place.
FAQ
Slayer filter questions, answered.
8 answers covering cartridges, intervals, warranty, and the local water profile.
What filter does my Slayer take?
Slayer doesn't ship with a proprietary cartridge, water treatment is dealer-installed. We standardize on Optipure BWS100 / BWS175 or Optipure Pro Series RO (OP175/12, OP300/16) sized to your daily volume. See the upstream systems table above.
How often should I replace my Slayer filter in the GTA?
Cartridge capacity is rated at 10°dKH. In moderate-hardness Toronto / Mississauga water, expect 9 to 12 months on a properly-sized cartridge. In harder York Region and Hamilton water, drop to 6 to 9 months. The full city-by-city schedule is in the GTA schedule table above.
Does Slayer require a specific filter brand for warranty?
Slayer doesn't mandate a specific brand but requires water in spec (typically 4-8°dH after the cartridge). Most installs default to Optipure. We document the install for warranty traceability.
Where does an upstream filter go in the install?
Between the building's water supply shutoff and the machine's inlet, usually mounted on the wall under a counter, with a dedicated shut-off valve and a pressure-relief loop. The cartridge head holds the calibrated bypass dial; the cartridge itself screws into the head. Service is a 5-minute cartridge swap without touching the machine itself.
Can one upstream filter feed multiple machines?
Yes if sized correctly, Everpure 7CB5-S and the larger BWT Bestmax XL are rated for multi-brewer feeds in office and foodservice manifolds. Beyond two espresso machines or two batch brewers, you're better off stepping up to a sized RO loop with magnesium remineralization. A single small cartridge feeding three high-volume machines will exhaust on capacity inside a quarter.
Do you carry the cartridges in your van for same-visit service?
Yes for the platforms we work on most, BWT Bestmax M/L/XL, Pentair Everpure Claris Ultra, Jura CLARIS Pro Smart, Saeco AquaClean CA6903, WMF AquaBasic V/M/XL, and Curtis CSC5CC00/CSC10CC00 ride on the truck. Less common cartridges (some Optipure tiers, Elektra Kwts factory softener, Melitta Cafina-branded) are ordered ahead of the visit so we land with the right part on the first trip.
Will you set up a maintenance schedule so I don't have to track it?
Yes. We commission with the install date logged against the cartridge's capacity rating and the site's measured daily volume. Our PM schedule lands cartridge swaps before exhaustion, descales the machine when the cartridge is being changed (so scale never reaches the boiler), and sends you the service log so you have warranty traceability for the manufacturer.
How much does a filter install or replacement actually cost?
Cartridge cost varies by tier, a single BWT Bestmax Premium L runs around $180 to $230 CAD, an Everpure Claris Ultra 500 sits in the same range. Installation labour on a new upstream loop is typically 1.5 to 2.5 hours depending on plumbing access. Routine cartridge swaps on an existing head are a 15-minute visit, usually folded into a PM call to save you a separate truck roll. We quote in writing before any work.
Track record
Receipts from a quarter-century of service work.
"
Bay Street tenant turnover, new machine, full install with water filtration and operator training in one visit. Done before the new team's first Monday.
Vivek · Facilities · Bay Street Tower
25+1
Years servicing equipment
4 hr2
Avg GTA response
92%3
First-visit resolution
4.74
Average client rating
1 Continuous service operations across the GTA since 2001. 2 Median on-site arrival window for urgent GTA calls placed during business hours. 3 Internal service tracking, 2024 to 2025 calendar years. 4 Calculated from verified client feedback over the past 24 months.
Slayer cartridge replacement, sized to your water.
We measure feed-water hardness on every install, dial the bypass to the manufacturer window, and put cartridges on capacity-tracked PM so nothing scales the boiler.
