Bezzera B2013 AL repair that shows up today. GTA-wide.

Yes, lever rebuilds are platform-knowledge work and we do them regularly. When the lever goes stiff or the shot drops off, the spring has usually lost tension and the piston seals have worn. We measure the spring force, replace it if it is below spec, rebuild the piston with fresh seals, lubricate with food-safe grease, and verify a smooth full-throw action.

Surface oxidization on the aluminum is normal over decades and is purely cosmetic. We clean it back and protect it with an aluminum-safe polish. Only where corrosion has gone deeper do we assess it for any structural impact, which is rare on these frames.

It is built for up to around 300 shots a day on its single heat-exchanger boiler, which suits a steady neighbourhood cafe or restaurant rather than a high-street machine pulling all day. Keep the scale down and it holds that figure for years.

Yes. On the automatic variants we diagnose at the board level, isolate the specific fault, and repair it where we can. Parts that need replacing come through the Italian distribution channel, and the dose programming gets verified before we leave.

After about five years a mechanical pressurestat usually needs more than an adjustment. We test the cut-in and cut-out against the gauge and reset the setpoint first; if the differential has collapsed we fit a Sirai or CEME replacement matched to the original setpoint.

Shot quality on these drifts from a mix of dispersion screen wear, grind, brew temperature, gicleur condition, and OPV setting, and on a lever build, spring tension and piston seal too. We work through each in order and recalibrate against reference shots rather than guessing.

Usually, yes. We source through the Italian distribution channel for current items, refurbisher networks for the older bits, and aftermarket equivalents we have validated against the platform. We will tell you up front if a part is genuinely unobtainable.

The level probe has scaled over and stopped conducting, so the machine reads the boiler as empty. We pull the probe, descale or replace it, and confirm the autofill responds on refill. It is a routine fix and a sign the water could use softening.

Flat rate for the visit, parts billed at their actual cost on top. You'll hear the rate when you book, and for bigger jobs we quote in writing on-site before any work starts. No estimate that balloons mid-job.

Same-day. Call in the morning and a technician is usually on-site before the day is out; calls placed later in the day book for the next morning. Urgent breakdowns get priority routing.

The GTA and most of the Golden Horseshoe: Toronto through Mississauga, Vaughan, and Markham, out to Oshawa, Hamilton, and Niagara. If you're not sure you're in range, call and we'll tell you straight.

No. We work call by call. Plenty of customers put us on a maintenance schedule eventually, but that's their choice after seeing the work, never a requirement.

Parts carry their manufacturer warranty, and we stand behind our labour: if the same fault recurs, call us and we'll review it. Specific terms are discussed upfront on each job, not promised in marketing copy.

On-site whenever possible, which is most of the time. If a job genuinely needs the bench, like a full boiler rebuild or major electronics work, we'll say so before anything leaves your building.

Call us or send the form on this page. We confirm the machine, the fault, and a time window the same day. If it's urgent, say so and we'll route the nearest technician.

Diagnosis first: we confirm the fault, tell you what caused it, and quote the fix before touching a wrench. Most repairs finish in that same visit because the common wear parts ride on the truck.

High-wear parts for the platforms we service constantly ride on the truck. Anything else we order, usually next-day where suppliers allow, and we tell you the lead time before committing you to anything.

Usually, yes. We service legacy machines for as long as parts can be sourced, and we're honest when a repair stops making financial sense against a replacement. You get the math, you make the call.

Often, but that's not the pitch. We quote against the actual work, not a factory pricing book, and we'll tell you when a manufacturer warranty claim is the better route. Transparency is the value; the price usually follows.

Yes, and we do it by default on the way out. Half of repeat faults trace back to skipped daily cleaning or wrong routine, so the technician walks your team through what actually matters before leaving.