BlueDot Power, built for volume
Your BlueDot Power runs hardest of the family, often unattended, so a fault costs real throughput. We repair the Power regularly: brew units worn by high cycle counts, self-cleaning milk faults, twin-grinder drift, and payment or screen lockups on vending setups. Give us the symptom and the parts for the likely fix come with us.
We'll get back to you today.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email support@grajqevci.com.
Carimali · High-volume fully automatic with touchscreen interface
The BlueDot Power is the highest-output member of the BlueDot family, rated for up to 300 cups a day. Twin grinders and a self-cleaning milk system keep it pouring in busy offices, hotels, and self-service sites where it runs for hours. On the bench the volume tells: accelerated brew-unit and burr wear, plus a milk circuit that depends on its automated clean running.
Why Grajqevci
Call in the morning and a technician is usually on-site before the day is out. Most Carimali BlueDot Power jobs get diagnosed and fixed on the first visit.
Commercial coffee equipment is all we do, and Carimali BlueDot Power is one of the platforms we know best. Not a generalist guessing at a service manual. Genuine OEM parts, industry-standard procedures.
Flat rate for the visit, with parts billed separately. For bigger jobs you'll see a written quote on-site before we proceed.
Skip the wait
Trusted by Toronto's most demanding teams
BlueDot Power faults we diagnose
These are the BlueDot Power faults we see on high-volume installs, with the cause behind each and how we resolve it.
Slow recovery or a temperature code on a high-output Power is scale plus sensor or element drift. We descale the heating circuit, test NTC readings and element output, correct the control fault, and clear the log.
A tray filling too fast under vending volume is a leak or a restricted drain. We pressure-test the brew and milk circuits, clear the drain restriction, and replace any leaking seals or lines.
A dose mismatch across the twin grinders is uneven burr wear. We weigh each side, inspect the burrs, recalibrate the grind-time targets, and replace burrs where one side has fallen below spec.
A frozen screen or stalled payment workflow is usually firmware or a loose harness, not the hardware. We hard-reset the controller, check firmware state and harness seating, and replace the display or integration board only when the fault repeats.
Under the Power's heavier daily volume the brew unit jams on grind buildup and accelerated wear. We pull it, clean the cams and piston path, replace the worn seals, lubricate the wear points, and verify clean cycling across repeated test drinks.
Foam that fades after a peak is residue and worn intake parts on a hard-run milk circuit. We disassemble and sanitize it, replace the O-rings and intake components, confirm the cleaning-solution dosing, and check foam on a test drink.
Your coffee emergency ends here
Call or submit the form. We confirm your address, model, and the issue.
An experienced technician arrives, runs full diagnostics, and identifies the root cause.
You receive a flat, itemized quote. Nothing proceeds without your green light.
We complete the repair, run a test cycle, and walk you through what to watch for.
Parts on the truck
The record
Bay Street tenant turnover, new machine, full install with water filtration and operator training in one visit. Done before the new team's first Monday.
*Estimated based on the approximate distance from our nearest service centre, average commute time, and median service-call length for one machine. Prices in Canadian dollars (CAD $). Final quote provided on-site after diagnosis.
FAQ
20 answers covering service, repair, parts, installation, warranty, and edge cases.
Updated August 2026
The Power logs high daily cycle counts, so the brew unit sees more wear than a lighter machine. We service it on a shorter interval, clean and lubricate the cam and piston path, replace seals before they fail, and verify clean cycling across repeated drinks.
The automated clean has to run on schedule with proper dosing, and residue means the dosing pump, cleaning solution, or a level sensor has dropped out. We verify the dosing, refill or repair as needed, and sanitize the milk circuit so foam comes back clean.
Yes. On vending and self-service installs the screen and payment terminal talk over a link that can drop, usually firmware or a loose harness rather than a dead board. We reset the controller, check the integration, and replace the board only if the fault repeats.
The Power steps the rating up to 300 cups a day and adds self-cleaning milk routines aimed at unattended use. The core touchscreen and brew-unit platform is shared, but the Power's milk automation and higher volume change how often the grinder and milk system need attention.
It is built for it, but slow recovery usually means scale or a tired element cutting the boiler's output. We descale the heating circuit, test the element and sensors, and confirm recovery under back-to-back drinks before clearing the log.
Uneven dosing is burr wear, and the busier hopper wears first. We weigh each side, inspect the burrs, recalibrate the grind-time targets, and replace burrs where one side has fallen below spec so both pour to the same weight.
More often than a lighter BlueDot, because the volume drives wear. We base the interval on your actual cycle counts and water, and a scheduled visit catches brew-unit and milk-system wear before it becomes downtime on an unattended machine.
Usually, yes. Even on a hard-run machine the common faults are wear parts that cost a fraction of replacement, and a brew-unit and milk-system refresh restores throughput. We quote it honestly against remaining life and let you decide.
Flat rate for the visit, parts billed at their actual cost on top. You'll hear the rate when you book, and for bigger jobs we quote in writing on-site before any work starts. No estimate that balloons mid-job.
Same-day. Call in the morning and a technician is usually on-site before the day is out; calls placed later in the day book for the next morning. Urgent breakdowns get priority routing.
The GTA and most of the Golden Horseshoe: Toronto through Mississauga, Vaughan, and Markham, out to Oshawa, Hamilton, and Niagara. If you're not sure you're in range, call and we'll tell you straight.
No. We work call by call. Plenty of customers put us on a maintenance schedule eventually, but that's their choice after seeing the work, never a requirement.
Parts carry their manufacturer warranty, and we stand behind our labour: if the same fault recurs, call us and we'll review it. Specific terms are discussed upfront on each job, not promised in marketing copy.
On-site whenever possible, which is most of the time. If a job genuinely needs the bench, like a full boiler rebuild or major electronics work, we'll say so before anything leaves your building.
Call us or send the form on this page. We confirm the machine, the fault, and a time window the same day. If it's urgent, say so and we'll route the nearest technician.
Diagnosis first: we confirm the fault, tell you what caused it, and quote the fix before touching a wrench. Most repairs finish in that same visit because the common wear parts ride on the truck.
High-wear parts for the platforms we service constantly ride on the truck. Anything else we order, usually next-day where suppliers allow, and we tell you the lead time before committing you to anything.
Usually, yes. We service legacy machines for as long as parts can be sourced, and we're honest when a repair stops making financial sense against a replacement. You get the math, you make the call.
Often, but that's not the pitch. We quote against the actual work, not a factory pricing book, and we'll tell you when a manufacturer warranty claim is the better route. Transparency is the value; the price usually follows.
Yes, and we do it by default on the way out. Half of repeat faults trace back to skipped daily cleaning or wrong routine, so the technician walks your team through what actually matters before leaving.
One call books a technician who knows high-volume Carimali installs.
Call (289) 217-3796 now →