!
Saturated group gasket leak
Group gaskets wear out like tires; the Spiritello's are no exception. We fit a fresh Kees-spec gasket and verify a clean seal across test shots.
The smallest Kees, taken serious
A Spiritello usually pours for a room that chose it over a super-automatic on purpose, so nobody wants to hear 'just get a new one' when it misbehaves. We repair these compact singles properly: brew boiler recalibration, gasket and bushing wear, joystick steam, pre-infusion checks. Small machine, same standards.
We'll get back to you today.
Thanks. We received your request.
A Grajqevci technician will get back to you today to confirm your machine and book the visit. If it's urgent, call us directly at (289) 217-3796.
Something went wrong sending your request.
Please try again, or call us directly at (289) 217-3796 and we'll book your service over the phone. You can also email [email protected].
Kees van der Westen · Premium specialty espresso, single-group compact
The Spiritello is the smallest machine Kees builds, a compact single group with the Spirit's architecture inside. It's rated for up to 150 shots a day and turns up in boutique offices, restaurants, and single-bar concepts that want real paddle espresso without a full-width machine. Two boilers, saturated group, joystick steam: nothing about it is cut down except the footprint. The service pattern matches its siblings, led by gaskets, bushings, and scale.
Why Grajqevci
Call in the morning and a technician is usually on-site before the day is out. Most Kees van der Westen Spiritello jobs get diagnosed and fixed on the first visit.
Commercial coffee equipment is all we do, and Kees van der Westen Spiritello is part of the weekly rotation. Not a generalist guessing at a service manual. Genuine OEM parts, industry-standard procedures.
Flat rate for the visit, with parts billed separately. For bigger jobs you'll see a written quote on-site before we proceed.
Skip the wait
Trusted by Toronto's most demanding teams
Spiritello faults we diagnose
The Spiritello shares its bones with the bigger Spirits, and these are the faults it shares too, with cause and fix for each.
Group gaskets wear out like tires; the Spiritello's are no exception. We fit a fresh Kees-spec gasket and verify a clean seal across test shots.
A paddle that resists the sweep needs new PTFE bushings. We replace them and lubricate the linkage.
Dispersion screens scale over and start dimpling. We pull, soak, inspect, and replace annually.
Brew pressure drift is a pump or OPV question. We measure at the portafilter and adjust or replace.
Pre-infusion curve drift comes down to the solenoid, inlet pressure, or the expansion valve. We log the curve and find which.
The Spiritello's brew boiler runs on a PID that drifts when the NTC or element ages. We test, descale, recalibrate, and replace what's out of spec.
Steam boiler scale builds quietly. We descale and check the element resistance while we're in there.
An under-machine leak gets a pressure test and a dye-trace, then the failing part replaced.
Play in the steam joystick means bushing wear. A replacement restores the action.
We probe the cool-touch wand's surface temperature and replace the assembly if the insulation has gone.
Display drift traces to the NTC or its connector. We test, reseat, and replace.
Electronics faults get diagnosed at board level, with parts sourced through the European channel.
Custom panel damage is fixed with factory parts and the finish preserved.
Quality drift means checking the dispersion screen, grind, brew temperature, and pre-infusion until the answer shows up. It typically does.
Older Spiritellos keep running on parts from the European specialty channel.
Your coffee emergency ends here
Call or submit the form. We confirm your address, model, and the issue.
An experienced technician arrives, runs full diagnostics, and identifies the root cause.
You receive a flat, itemized quote. Nothing proceeds without your green light.
We complete the repair, run a test cycle, and walk you through what to watch for.
Parts on the truck
The record
Quick response, exceptional service, and fair pricing. That's what they're all about.
*Estimated based on the approximate distance from our nearest service centre, average commute time, and median service-call length for one machine. Prices in Canadian dollars (CAD $). Final quote provided on-site after diagnosis.
FAQ
21 answers covering service, repair, parts, installation, warranty, and edge cases.
Updated July 2026
Essentially yes: the Spirit's two-boiler architecture, saturated group, and paddle in a compact single-group frame. It gives up capacity, not precision. From the service side it behaves like its bigger siblings and uses the same kind of platform-specific parts.
Scale in the brew boiler, a drifting NTC sensor, or a PID that needs recalibration. We test the sensor against its resistance table, descale, recalibrate, and replace whatever reads out of spec. The machine should hold its setpoint quietly again afterwards.
It's rated for up to 150 shots a day, which fits a boutique concept, a restaurant, or an office nicely. A single compact group sets the pace, so a hard morning rush will queue. If your volume is regularly testing the rating, it's worth a conversation before the wear shows it.
Worn PTFE bushings in the linkage. We replace them, clean and lubricate the pivot, and the sweep comes back to how it felt new. It's routine work when it's done before something else wears in sympathy.
Both boilers get descaled, the element resistance gets checked, and the dispersion screen gets pulled and soaked while we're at it. On most municipal water an annual cycle is the right rhythm, sooner if the supply is hard. Skipping it is the most expensive thing you can do to this machine for free.
Now, while it's only a bushing. Play in the pivot works through to the microvalve seals, and a valve leaking past its seat is a bigger rebuild. Caught early, it's a small job.
The quiet suspects, in order: a scaled dispersion screen, grind drift, brew temperature offset, and pre-infusion behaviour. We work through each and recalibrate. Flat shots almost always trace to one of the four.
Yes, exactly as much as the big ones. The Spiritello carries the same kind of boilers and the same intolerance of scale, just in a smaller box. Proper filtration is the difference between a machine that lasts twenty years and one that needs an element in three.
Kees builds for twenty-plus years of service, and the Spiritello is no exception. Gaskets, bushings, screens, and descales on schedule are what get it there. We've yet to meet a well-watered Kees that aged badly.
Flat rate for the visit, parts billed at their actual cost on top. You'll hear the rate when you book, and for bigger jobs we quote in writing on-site before any work starts. No estimate that balloons mid-job.
Same-day in most cases. Call in the morning and a technician is usually on-site before the day is out; calls placed later in the day book for the next morning. Urgent breakdowns get priority routing.
The GTA and most of the Golden Horseshoe: Toronto through Mississauga, Vaughan, and Markham, out to Oshawa, Hamilton, and Niagara. If you're not sure you're in range, call and we'll tell you straight.
No. We work call by call. Plenty of customers put us on a maintenance schedule eventually, but that's their choice after seeing the work, never a requirement.
Parts carry their manufacturer warranty, and we stand behind our labour: if the same fault recurs, call us and we'll review it. Specific terms are discussed upfront on each job, not promised in marketing copy.
On-site whenever possible, which is most of the time. If a job genuinely needs the bench, like a full boiler rebuild or major electronics work, we'll say so before anything leaves your building.
Call us or send the form on this page. We confirm the machine, the fault, and a time window the same day. If it's urgent, say so and we'll route the nearest technician.
Diagnosis first: we confirm the fault, tell you what caused it, and quote the fix before touching a wrench. Most repairs finish in that same visit because the common wear parts ride on the truck.
High-wear parts for the platforms we service constantly ride on the truck. Anything else we order, usually next-day where suppliers allow, and we tell you the lead time before committing you to anything.
Usually, yes. We service legacy machines for as long as parts can be sourced, and we're honest when a repair stops making financial sense against a replacement. You get the math, you make the call.
Often, but that's not the pitch. We quote against the actual work, not a factory pricing book, and we'll tell you when a manufacturer warranty claim is the better route. Transparency is the value; the price usually follows.
Yes, and we do it by default on the way out. Half of repeat faults trace back to skipped daily cleaning or wrong routine, so the technician walks your team through what actually matters before leaving.
One call, a clear diagnosis, and parts that actually fit a Kees.
Call (289) 217-3796 now →